Release 01.10.07
-----------------------------------------------------------
- Fixed: ProBatch+ problem during discharge sends weight error

Release 01.10.06
-----------------------------------------------------------
- Fixed: Component D4_Dialog is directly approved, message
         never shown

Release 01.10.05
-----------------------------------------------------------
- Fixed: Recipe start and parameter "Production with recipe
         total" is activated in ProBatch+.
- Fixed: SPM set/reset from different weighing points.

Release 01.10.04
-----------------------------------------------------------
- Fixed: SPMinBit and SPMinTareBit are now triggered on
  rising edge (D1, D2).

Release 01.10.03
-----------------------------------------------------------
- Fixed: pi.oActual value is set one state earlier for
  ProBatch+ (D2).

Release 01.10.02
-----------------------------------------------------------
- Changed: Manual dosing ( D1, D2 ), included an optional
  start dialog. the user can sync tare function. acknowledge
  by key or spmintare.

Release 01.10.01
-----------------------------------------------------------
- Fixed: Mantis 1407, Analog Output 4..20mA, offset error
- Fixed: Mantis 351

Release 01.10.00
-----------------------------------------------------------
- Compiled using FBLib-S88 Version 01.10.00 ( required )
- Manual phase ( D1, D2 ): the optional dialog is done
  before dosing any material.
- Operating of D1 in case of tolerance alarm is now
  similar to automatic dosing ( B1, ... ).'continue' is
  the the same on PC and on the controller. 'abort' on PC
  does not have the function of 'accept' on the controller
  and aborts the phase ( line marked: '*' ).
- Tolerance alarm, flow warning and phase held signals are
  now in virtual SPM:
  Bit 16: tolerance alarm WP-A
      17: flow warning WP-A
      18: phase in held state WP-A
  Bit 24: tolerance alarm WP-B
      25: flow warning WP-B
      26: phase in held state WP-B
- SPMout for the timer phase ( D3 ) is set again again
  after restarting a stopped phase.
- Text in BCD-output-configuration changed
- Console program 'dbg' dumps virtual SPM up to byte 71.

Release 01.04.01
-----------------------------------------------------------
- The virtual SPM is now 575 bite. Bit 512 ... 575 are
  copied from bit 128 ... 159 with AND of coarse / fine
  for both weighing points. E.g.:
  bit 512 := bit 128 AND coarse WP-A
  bit 528 := bit 128 AND fine WP-A
  bit 544 := bit 144 AND coarse WP-B
  bit 560 := bit 144 AND fine WP-B
  This area can only be connected to the binary outputs.

Release 01.04.00
-----------------------------------------------------------
- Version 01.02.01of FBLib-S88 is required for compiling.
- Changed in FBLib-S88 D7-component:
  SPMOut is not longer reset at termination of the phase.
- New phase type: D1_TARE will stop for operator
  interaction to tare the scale.
- New phase type: D4_MESSAGE waits for user action (like
  D4_DIALOG dialog=5 but receives signal 'Manual' from
  oposite WP).

Release 01.02.04
-----------------------------------------------------------
- Changed in FBLib-S88 D1/D2-component:
  Allow some time for standstill and taring ( <= 10s )

Release 01.02.03
-----------------------------------------------------------
- Analogue output 'Extern' is taken now correctly from
  address 3 in the virtial for 0/4 ... 20 mA.

Release 01.02.02
-----------------------------------------------------------
- Changed in FBLib-S88 D5-component:
  SPMout is reset after stop command.
  Active (bit 0 in oPhaseFlags) is set after start command.

Release 01.02.01
-----------------------------------------------------------
- new PR1750-50 ( version in *.p32 )

Release 01.02.00
-----------------------------------------------------------
- Compiled for new GSD files

Release 01.00.00
-----------------------------------------------------------
First Release